Logo

P0377 Engine Trouble Code

P0377 Engine

When you check engine light came on code P0377 the reason should be Engine Light ON (or Service Engine Soon Warning Light). However your vehicle's manufacturer may have a different definition for the P0377 OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.

When the DTC check engine light comes P0377 code on the first you can check is the gas related maybe gas cap. Pull over, retighten it, and take a look at the cap to see if it has any cracks inside. Go on driving and to see if the check engine light turns off automaticly. On the other hand, you can buy a gas cap for about $4.5 at an auto parts store. All you need to do is take the old one take off and take on the new one. If you've already bought it to the store, you might as well just replace the cap. While not car-threatening, it's good to take care of this right away to improve gas mileage/km.

P0377 Code Meaning :

P
OBD-II Diagnostic Powertrain (P) Trouble Code For Engine
0
Intake Valve Control Solenoid Circuit Low
3
Fuel Rail Pressure Sensor Circuit Malfunction
7
Injection lump Fuel Metering Control 'B' High (Cam/Rotor/Injector)
7
Crankshaft Position Sensor B Circuit Malfunction

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

P0377 OBD-II Diagnostic Powertrain (P) Trouble Code Description

P0377 OBD-II Trouble Code The optical sensor provides a high resolution signal to the Powertrain Control Module ( P0377 code. Fuel Rail Pressure Sensor Circuit Malfunction and Injection lump Fuel Metering Control 'B' High (Cam/Rotor/Injector) causes most of code P0377.

Reason For P0377 Code

The reason of P0377 OBD-II Engine Trouble Code is Fuel Rail Pressure Sensor Circuit Malfunction.

P0377 DTC reports a sensor fault, replacement of the sensor is unlikely to resolve the underlying problem. The engine error is most likely to be caused by the systems that the sensor is monitoring, but might even be caused by the wiring to the sensor itself.

How To Repair P0377 Code

Before starting let's see P0377 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access P0377 code stored in the ECU.
  • Technicians will note P0377 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

The reductant injector is part of the system that reduces the gas that is expelled through either the catalytic converter in gas engines, or the particulate filter in diesel engines. There are sensors in the exhaust system, used by the reductant injector to input voltage readings to the PCM.

P0377 code is stored again, the mechanic will perform a visual inspection of the pressure control solenoid and related systems. If any circuits or connections are damaged or loose, they will resolve these issues and move on to retest the system.

Sometimes P0377 code comes with P037700 code.

Diagnosis Of Engine Error OBD Code P0377

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P0377 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P0377 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.